Garage door truck inventory works when every part has a target, every move gets logged, and every truck gets counted once a week. Base each target on what that truck actually uses, take parts off when the job is invoiced, and compare the count against what the records say should be there. The gap tells you what to fix.
Garage door truck inventory is hard for a plain reason: your stock is rolling around town in several vehicles, and the people moving it are busy working. Parts leave the shelf at 7am, change trucks in a parking lot at noon, and go on a door at 4pm. If any of that lives only in somebody's head, your numbers are wrong by Friday.
You do not need a warehouse manager to fix this. You need a short list, a few rules, and a quick count on each truck every week. Here is how to set it up.
What a short truck costs you
The obvious cost is the return trip. The tech drives back to the shop or the supply house, the next customer's window slips, and the dispatcher starts making phone calls. On a broken spring call the homeowner's car may be stuck inside, and they may not wait for you to come back.
The quieter cost is on the other side. A truck loaded with everything anybody might ever need has your cash riding around on it, and nobody can tell you how much. Parts that have not moved in a year still get dented, rusted and lost. The goal is not the most stock. It is the right stock, and knowing that you have it.
Step 1: Decide what rides on the truck
Do not start from a generic list. Pull the last 90 days of invoices and rank parts by how often they were used. Most of what you need to carry will be obvious once you see it. The slow movers near the bottom are the shelf's job, not the truck's.
| Category | What to look at | Where the trouble usually is |
|---|---|---|
| Springs | Your most-used torsion sizes by wire, inside diameter and length, left and right wind, plus common extension springs | Too many sizes on the truck. Count each size and wind as its own line. |
| Cables and drums | Common lengths, and the drums that fit the doors you see most | Cables get used on spring jobs without being written down. |
| Rollers and hardware | Rollers, hinges, bearings, brackets, fasteners | Cheap, loose and rarely counted. Track by the box or set, not the piece. |
| Seal | Bottom seal and retainer you install most | Partial rolls. Pick one way to count them and stick to it. |
| Opener parts | Sensors, gears, remotes, keypads, logic boards for the brands you see | Small, expensive and easy to lose. |
| Openers | One or two models you sell the most | High dollar per unit. One missing opener matters more than a box of rollers. |
A starting framework. Your invoices should decide the actual list for each truck.
Give each truck its list on purpose. A tech who mostly runs service calls does not need the same load as one who does door installs.
Step 2: Set a target for every part
A target is the number that should be on the truck after it gets restocked. The math fits on a napkin:
Target = average weekly use × weeks between restocks + a small buffer.
| Part | Used per week | Weeks between restocks | Buffer | Target |
|---|---|---|---|---|
| Most-used torsion spring (each) | 6 | 1 | 2 | 8 |
| Second-most-used torsion spring (each) | 3 | 1 | 2 | 5 |
| Lift cables (pair) | 4 | 1 | 2 | 6 |
| Rollers (box) | 2 | 1 | 1 | 3 |
| Bottom seal (roll) | 1 | 2 | 1 | 3 |
| Best-selling opener (each) | 2 | 1 | 1 | 3 |
Illustrative numbers for one service truck. Use your own invoices.
Two-spring doors use them in pairs, so count that when you pull usage. Then watch the targets for a few weeks. If a truck keeps running out, raise the number. If a part keeps sitting there, lower it or move it to the shelf.
Step 3: Make every move a logged move
Stock only moves in a few ways. Write a rule for each one, and make it quick enough that a tech will follow it at the end of a long day.
- Supplier to shop. Receive every order against the supplier, including what you paid. This sets your stock and your cost.
- Shop to truck. A tech grabbing a box of rollers logs it before he leaves. Otherwise the shelf looks short and the truck looks fine.
- Truck to truck. A handoff in a parking lot gets logged by one of the two techs on the spot.
- Truck to job. Every part on the door goes on the invoice. Parts come off stock when the job is invoiced, so nobody has to remember the second spring later.
- Job to shelf. If a job is cancelled, the parts go back. If a part gets returned to the supplier, that gets recorded too.
Packages are where this often breaks. A rebuild sold as one line still used springs, cables and rollers, so the parts inside have to come off stock too. If you are building good, better, best options, list what goes in each package before the first tech sells one. Part costs matter beyond the shelf too: if you pay commission on profit, a wrong cost changes somebody's check.
Step 4: Count every truck once a week
Pick a slot and keep it. Friday afternoon or first thing Monday both work. The tech counts the truck against the list, and the office compares that to what the records say should be there. Everything that does not match goes on a short list.
Weekly matters because memory fades. On Monday a tech can tell you the missing cable went on Thursday's rebuild and never made the invoice. In six months nobody can tell you anything.
| Truck | Part | Expected | Counted | Difference | Dollars at cost |
|---|---|---|---|---|---|
| Truck 1 | Torsion spring | 8 | 7 | -1 | -$30 |
| Truck 2 | Lift cables (pair) | 6 | 4 | -2 | -$24 |
| Truck 2 | Opener | 3 | 2 | -1 | -$190 |
| Truck 3 | Torsion spring | 5 | 6 | +1 | +$30 |
| Net for the week | -$214 | ||||
Illustrative numbers. A week like this repeated for 50 weeks would be $10,700 a year.
Step 5: Read the differences before you accuse anybody
A lot of count differences are paperwork. Each one has a usual explanation, and each explanation points to a different fix:
- Short on a part, and the tech remembers the job. The part got used but never invoiced. That is money you did not bill. Check the job, and make it right if you can.
- Over on one truck, short on another. Probably an unlogged handoff. Remind both techs and fix the numbers.
- Over by one or two after a shop visit. Probably an unlogged shop pickup. Check the shelf.
- The same part short on the same truck, week after week. Now you have a pattern worth a direct conversation. Look at the movement history first so you are talking about facts.
Be careful about charging techs for shortages. The U.S. Department of Labor's Fact Sheet 16 says deductions for employer-benefit costs such as tools or losses cannot take pay below minimum wage or cut into required overtime, and your state may be stricter. Ask your attorney or accountant before you deduct anything.
The mistakes that sink garage door truck inventory
- Counting once a year. You learn the size of the loss, but not where or when it happened.
- Counting without acting. If nobody ever asks about a difference, techs stop taking the count seriously.
- Tracking every washer. Spend your attention where the money is: springs, openers, cables and opener parts. Group cheap fasteners into a box or set, or expense them.
- An open shelf with no pickup rule. If parts can leave the shop unrecorded, every number after that is a guess.
- Stale costs. When supplier prices change and nothing gets updated, your inventory value and your job profit are both off. Ask your accountant how to treat inventory and count adjustments on your books.
What to do Monday morning
- Pull 90 days of invoices and rank the parts by how often they were used.
- Pick your top 20 or so parts. Those are the only ones you track at first.
- Count one truck by hand and write down the targets for it.
- Tell the crew the rule: nothing leaves the shelf or changes trucks without being logged, and every part on the door goes on the invoice.
- Count again next week, go through the differences together, and fix what you find.
- Once one truck is working, add the next one. Then add parts to the list.
How ServiceBuilt handles it
ServiceBuilt tracks stock in the shop and on every truck. When a job is invoiced, its parts come off the tech's truck first, then the shop shelf, including the parts inside a package like a rebuild. Techs log shop pickups and truck-to-truck moves from the app, weekly counts flag what does not match, and a daily alert lists what is low. See how inventory and truck stock work; it is on the Powerhouse plan, $448 a month with unlimited technicians.
Common questions
What inventory should a garage door technician carry on the truck?
Enough to finish your most common calls on the first trip: your most-used torsion and extension springs, lift cables, rollers, drums, bearings, hinges, seal, sensors, opener parts and one or two of the openers you sell most. Your own invoices should set the list, not a generic one. Pull the last 90 days, rank parts by how often they were used, and stock what comes up regularly.
How often should you count garage door truck inventory?
Weekly works well for most shops. A weekly count is short enough to do fast, and it is recent enough that the tech can still remember what happened to a missing part. A yearly count tells you that stock is gone but not when or where it went.
How do you set stock levels for each truck?
Use a target for each part: average weekly use, times the number of weeks between restocks, plus a small buffer for a busy week. Set it by truck if your techs run different work, and review the targets every few months, since seasons and your job mix change what gets used.
Can I charge a technician for missing parts?
Be careful. Under the federal Fair Labor Standards Act, deductions for losses that benefit the employer cannot take pay below minimum wage or cut into required overtime, and some states are stricter. Talk to your attorney or accountant before deducting anything from pay. Fixing the logging and following up on repeat shortages is the safer first step.
